Red Hat Enterprise Linux 2.1
Red Hat Enterprise Linux 2.1
Red Hat Enterprise Linux 2.1
Support
This guest operating system is supported on the following VMware products:
| • |
|
VMware Workstation 4.0, 4.0.1, 4.0.2, 4.0.5, 4.5, 4.5.1, 4.5.2, 5.0, 5.5, 5.5.1, 5.5.2-AS, ES, WS
Update 6 supported on Workstation 5.0, 5.5, 5.5.1, 5.5.2
Update 7 supported on Workstation 5.5, 5.5.1, 5.5.2
Experimental support for 2-way Virtual SMP on Workstation 5.5, 5.5.1, 5.5.2 |
| • |
|
VMware ACE 1.0, 1.0.1, 1.0.2-AS, ES, WS
Update 6 supported on VMware ACE 1.0.1, 1.0.2 |
| • |
|
VMware GSX Server 3.0, 3.1, 3.2, 3.2.1-AS, ES, WS
Update 6 supported on GSX Server 3.2, 3.2.1 |
| • |
|
VMware Server 1.0
Experimental support for 2-way Virtual SMP on VMware Server 1.0 |
| • |
|
VMware ESX Server 2.0, 2.0.1, 2.1, 2.1.1, 2.1.2, 2.5, 2.5.1, 2.5.2, 2.5.3, 3.0-AS, ES, WS
Update 6 supported on ESX Server 2.5, 2.5.1, 2.5.2, 2.5.3, 3.0
Update 7 supported on ESX Server 2.5.2, 2.5.3, 3.0
Virtual SMP supported |
Note: If you are installing a guest operating system through VMware VirtualCenter, be sure it is supported under the VMware product-ESX Server or GSX Server-on which you are running the virtual machine.
Red Hat Enterprise Linux 2.1
General Installation Notes
Be sure to read
General Guidelines for All VMware Products as well as this guide to installing your specific guest operating system.
The easiest method of installing Red Hat Enterprise Linux 2.1 in a virtual machine is to use the standard Red Hat distribution CD. The notes below describe an installation using the standard distribution CD; however, installing Red Hat Enterprise Linux 2.1 via the boot floppy/network method is supported as well. If your VMware product supports it, you can also install from a PXE server.
Before installing the operating system, be sure that you have already created and configured a new virtual machine.
RHEL 2.1 WS on VMware ESX Server: If you use a vlance network adapter in the virtual machine, you must use an LSI Logic SCSI adapter. If you use a vmxnet network adapter, you can use either a BusLogic or an LSI Logic SCSI adapter.
Note: You should not run the X server that is installed when you set up Red Hat Enterprise Linux 2.1. Instead, to get an accelerated SVGA X server running inside the virtual machine, you should install the VMware Tools package immediately after installing Red Hat Enterprise Linux 2.1.
Note: With many Linux guest operating systems, various problems have been observed when the BusLogic virtual SCSI adapter is used with VMware virtual machines. VMware recommends that you use the LSI Logic virtual SCSI adapter with this guest operating system.
Red Hat Enterprise Linux 2.1
Installation Steps
Note: Unless you are running a multiprocessor virtual machine under VMware ESX Server, pay particular attention to the notes in
step 6 about how to avoid installing an inappropriate kernel.
1 Insert the Red Hat Enterprise Linux 2.1 CD-ROM in the CD-ROM drive.
2 Power on the virtual machine to start installing Red Hat Enterprise Linux 2.1.
You must install Red Hat Enterprise Linux 2.1 using the text mode installer, which you can choose when you first boot the installer. At the Red Hat Enterprise Linux 2.1 CD boot prompt, you are offered a number of choices, including the following:
To install or upgrade Red Hat Linux ... in graphical mode ...
To install or upgrade ... in text mode, type: text <ENTER>...
...
Use the function keys listed below ...
To choose the text mode installer, type text and press Enter.
3 Follow the installation steps as you would for a physical machine. Be sure to make the choices outlined in the following steps.
4 Choose the language and keyboard, and then in the Installation Type screen, choose either Advanced Server or Custom for the installation type.
5 In the Mouse Selection screen, choose Generic - 3 Button Mouse (PS/2) and select the Emulate 3 Buttons option for three-button mouse support in the virtual machine. If you have a wheel mouse, you can choose Generic Wheel Mouse (PS/2).
6 VMware GSX Server only: In the Package Group Selection screen, choose Software Development and Select individual packages. In the Individual Package Selection screen, use the arrow keys to move down to System Environment/Kernel and press Enter. Be sure that kernel-smp is deselected (no asterisk should appear between the brackets). The SMP kernel is not supported in a GSX Server virtual machine. You do not need to change any other selections.
VMware ESX Server or VirtualCenter if installing to an ESX Server machine without virtual SMP: In the Individual Package Selection screen, use the arrow keys to move down to System Environment/Kernel and press Enter. Be sure that the following kernels are deselected (no asterisk should appear between the brackets):
n kernel-enterprise
n kernel-smp
n kernel-summit
VMware ESX Server or VirtualCenter if installing to an ESX Server machine with virtual SMP: In the Individual Package Selection screen, use the arrow keys to move down to System Environment/Kernel and press Enter.
n If you are installing a multiprocessor virtual machine, be sure kernel-smp is selected.
n If you are installing a uniprocessor virtual machine, be sure the following kernels are deselected: kernel-enterprise, kernel-smp and kernel-summit.
For additional information on using uniprocessor and multiprocessor kernels with a Red Hat Enterprise Linux 2.1 virtual machine under VMware ESX Server, see the release notes at
www.vmware.com/support/esx21/doc/releasenotes_esx21.html#vmpkernel.
7 Allow automatic partitioning of the disk to occur in the Automatic Partitioning screen or partition the virtual disk manually if you do not want to use the Red Hat defaults.
8 You might see a warning that says:
The partition table on device sda was unreadable. To create new partitions, it must be initialized, causing the loss of ALL DATA on the drive.
Would you like to initialize this drive?
This does not mean that anything is wrong with the hard drive on your physical computer. It simply means that the virtual hard drive in your virtual machine needs to be partitioned and formatted. Select the Yes button and press Enter. Also note that sda appears in the message as the device name if the virtual disk in question is a SCSI disk; if the virtual disk is an IDE drive, hda appears in the message as the device name instead.
9 If your computer is connected to a LAN that provides DHCP support, in the Network Configuration screen, you can select the option Use bootp/dhcp. If you prefer, you can also set the networking parameters manually.
10 In the Video Card Configuration screen, choose Generic SVGA.
This completes basic installation of the Red Hat Enterprise Linux 2.1 guest operating system.
Red Hat Enterprise Linux 2.1
VMware Tools
Be sure to install VMware Tools in your guest operating system. For details, see the manual for your VMware product or follow the appropriate link in the knowledge base article at
www.vmware.com/support/kb/enduser/std_adp.php?p_faqid=340.
Do not start the X server in the guest operating system until you install VMware Tools.
Red Hat Enterprise Linux 2.1
Enabling Sound After Installing Red Hat Enterprise Linux 2.1
VMware GSX Server: The sound device is disabled by default and must be enabled with the virtual machine settings editor (VM > Settings) after the operating system has been installed. To set up the virtual machine to play sound, see Configuring Sound in the GSX Server documentation.
Red Hat Enterprise Linux 2.1
Known Issues
Red Hat Enterprise Linux 2.1
Guest Screen Saver
VMware GSX Server: On a Linux host with an XFree86 3.x X server, it is best not to run a screen saver in the guest operating system. Guest screen savers that demand a lot of processing power can cause the X server on the host to freeze.
Red Hat Enterprise Linux 2.1
Migration to a Different Processor
VMware recommends you do not migrate a Red Hat Enterprise Linux 2.1 virtual machine between hosts when one host is running on an AMD processor and the other is running on an Intel processor.
During installation, Red Hat Enterprise Linux 2.1 chooses a kernel that is optimized for the specific processor on which it is running. The kernel might contain instructions that are available only on that processor. These instructions can have adverse effects when run on a host with the wrong type of processor.
Thus, a Red Hat Enterprise Linux 2.1 virtual machine created on a host with an AMD processor might not work if migrated to a host with an Intel processor. The reverse is also true: a Red Hat Enterprise Linux 2.1 virtual machine created on a host with an Intel processor might not work if migrated to a host with an AMD processor.
This problem is not specific to virtual machines and would also occur on physical computers. For example, if you moved a hard drive with a Red Hat Enterprise Linux 2.1 installation from an AMD machine to an Intel machine, you would experience problems trying to boot from that drive.
Red Hat Enterprise Linux 2.1
Disable PAE in ESX Server Virtual Machines
EXS Server 2.5.x: Although ESX Server 2.5.x virtual machines are compatible with Physical Address Extension (PAE), they are not optimized for it. As a result, guest operating systems with PAE enabled might experience poor performance. For best performance, VMware recommends that you disable PAE in guest operating systems. For more information and instructions on disabling PAE, see the knowledge base article at
www.vmware.com/support/kb/enduser/std_adp.php?p_faqid=2020.
EXS Server 3.0: Note that disabling PAE also disables NX (no execute) and ED (execute disabled) features found in recent AMD and Intel processors. These features are not supported by ESX Server versions before ESX Server 3.0.
