Turbolinux 7.0
Turbolinux 7.0
Turbolinux 7.0
Support
This guest operating system is supported on the following VMware products:
| • |
|
VMware Workstation 4.0, 4.0.1, 4.0.2, 4.0.5, 4.5, 4.5.1, 4.5.2, 5.0, 5.5, 5.5.1, 5.5.2
Experimental support for 2-way Virtual SMP on Workstation 5.5, 5.5.1, 5.5.2 |
| • |
|
VMware ACE 1.0, 1.0.1, 1.0.2 |
| • |
|
VMware GSX Server 3.0, 3.1, 3.2, 3.2.1 |
| • |
|
VMware Server 1.0
Experimental support for 2-way Virtual SMP on VMware Server 1.0 |
Note: If you are installing a guest operating system through VMware VirtualCenter, be sure it is supported under the VMware product-ESX Server or GSX Server-on which you are running the virtual machine.
Note: With many Linux guest operating systems, various problems have been observed when the BusLogic virtual SCSI adapter is used with VMware virtual machines. VMware recommends that you use the LSI Logic virtual SCSI adapter with this guest operating system.
Turbolinux 7.0
General Installation Notes
Be sure to read
General Guidelines for All VMware Products as well as this guide to installing your specific guest operating system.
The easiest method of installing Turbolinux 7.0 in a virtual machine is to use the standard Turbolinux 7.0 distribution CD. The notes below describe an installation using the standard distribution CD; however, installing Turbolinux 7.0 via the boot floppy/network method is supported as well. If your VMware product supports it, you can also install from a PXE server.
Before installing the operating system, be sure that you have already created and configured a new virtual machine.
Note: During the Turbolinux 7.0 installation, a standard VGA16 X server (without support for the VMware display adapter) is installed. To get an accelerated SVGA X server running inside the virtual machine, install the VMware Tools package immediately after installing Turbolinux 7.0, before you start the X server.
Turbolinux 7.0
Installation Steps
1 Insert the Turbolinux 7.0 CD No. 1 in the CD-ROM drive.
2 Power on the virtual machine to start installing Turbolinux 7.0.
3 Follow the installation steps as you would for a physical PC until you get to the selection screen described in the next step.
4 In the Configure Monitor screen, follow the defaults to configure an X server. This is necessary even though you will install a different X server with VMware Tools after you finish installing the guest operating system.
5 Finish installing Turbolinux 7.0 as you would on a physical computer.
At this point Turbolinux 7.0 boots and a login screen appears.
Turbolinux 7.0
VMware Tools
Be sure to install VMware Tools in your guest operating system. For details, see the manual for your VMware product or follow the appropriate link in the knowledge base article at
www.vmware.com/support/kb/enduser/std_adp.php?p_faqid=340.
Do not start the X server in the guest operating system until you install VMware Tools.
VMware GSX Server: If you plan to test scripts in a Turbolinux 7.0 guest operating system, you must update the Turbolinux guest operating system. This is a known issue with Turbolinux. Go to ftp://ftp.turbolinux.com/pub/TurboLinux/TurboLinux/ia32/Workstation/7/updates/RPMS/initscripts-7.0.0-18.i586.rpm. For more information about running scripts in a guest operating system, see Executing Scripts When the Virtual Machine's Power State Changes in the GSX Server documentation.
Turbolinux 7.0
Enabling Sound After Installing Turbolinux 7.0
VMware GSX Server: The sound device is disabled by default and must be enabled with the virtual machine settings editor (VM > Settings) after the operating system has been installed. To set up the virtual machine to play sound, see Configuring Sound in the GSX Server documentation.
Turbolinux 7.0
Known Issues
Turbolinux 7.0
Guest Screen Saver
On a Linux host with an XFree86 3.x X server, it is best not to run a screen saver in the guest operating system. Guest screen savers that demand a lot of processing power can cause the X server on the host to freeze.
